Tips From the Moving Business Pros: How to Move a Pinball Device
With pinball making a huge revival throughout the country, Gentle Giant desires to make certain that these classic, gorgeous devices remain damage-free while being transported. Oh, and we want the people moving them to be safe, too.
Initially look, pinball machines can appear daunting to move since of their size, weight, and fragility. Fortunately, our competent Giants have a couple of techniques up their sleeves to ensure your pinball is moved with ease.
Folding Down the Headbox
The majority of contemporary pinballs (made in the last Twenty Years approximately) have a hinge system which allows the headbox to be folded down. Early pinball devices had their headboxes bolted on, utilizing either 2 or 4 bolts. All Electro-Mechanical pinballs use this system, along with the early Solid State devices.
Later on machines have hinges and utilize a locking system to keep the headbox upright. There might also be two bolts inside as added security, in case the lock is broken or mistakenly un-latched.
For Electro-Mechanical pinball machines, you need to eliminate the headbox rear gain access to panel to get to the bolts and plugs within. Usually this panel has a lock on it to keep it in place, but gradually the secret might have been lost. On a regular basis, there is a screw keeping this panel in place.
When inside, eliminate the bolts and disconnect the large connectors that have electrical wiring going down into the device. You might wish to label these ports to put them back in the best area, however they need to be various sizes, making it difficult to plug back incorrectly.
You can now eliminate the headbox totally, or fold the headbox down onto the playfield glass. Ensure you utilize some foam, heavy cardboard, or blankets to secure the headbox from rubbing on the cabinet. Foam is best, as it will assist keep the back glass in place.
Early Solid State Pinballs
For early Solid State Pinballs, you will need to eliminate the back glass. There is a lock situated on the headbox in among 3 locations: the left-hand side at the top, right-hand side at the top or on top of the headbox in the center.
As soon as opened, get rid of the back glass by lifting it up using the lift channel (at the bottom of the glass), and then pull it out from the bottom.
Then, open up the back box lamp panel by lifting the lock situated on either the left-hand side or right-hand side. The panel can now swing out to you, and offer you access to the circuit boards, plugs, and the bolts. Some Gottlieb pinballs require you to lift up the lamp panel in order to swing it open.
Now that you are inside, you can remove the bolts, and any plugs that have wires going down into the device. You may wish to identify these plugs to put them back in the best area. You might not have to get rid of the plugs, as the circuitry needs to be long enough to permit the headbox to be folded down.
At this point, you can lock up the lamp panel and replace the back glass.
Modern Solid State Pinballs
For Data East, Sega, and Stern Modern pinballs, there is a turnable latch system located at the back of the headbox. Using the supplied key, turn the latch 90 ° counter-clockwise.
For Williams, Bally, and Gottlieb, you can easily unlatch the back box at the back of the device. This is an easy setup and requires no tools.
You're done if you can now fold down the head box onto the cabinet. Ensure you utilize some foam, heavy cardboard, or blankets to secure the headbox from rubbing on the cabinet. Foam is best, as it will likewise assist keep the back glass in location.
If you can not fold the head box down, then you have to get in. There is a lock situated at the top of the back glass in the center. Utilize the provided secret to unlock, and get rid of the back glass by lifting it up from the bottom, and then pulling it out from the bottom.
Next, you will need to remove the display panel. You can do this by lifting it up and out. Open the lamp panel. There will be a latch located on either the right-hand or left-hand side. (Some newer Williams and Bally pinballs do not have a separate amp panel, it belongs to the back glass panel. And later Sega and Stern pinballs use a fluorescent tube for the back glass lighting).
Remove the two bolts, put the back box back together, and fold down the head box onto the cabinet. Make certain you utilize some foam, heavy cardboard, or blankets to secure the headbox from rubbing on the cabinet. Foam is best, as it will likewise assist keep the back glass in location.
Getting rid of the Legs.
Pinball Device legs are held in place by eight bolts. The modern pinballs have captive nuts or threaded plates inside for the bolts to screw into.
But these captive nuts and threaded plates can be damaged, and using additional nuts might have been needed. If this is the case, you will need to open up the front door of the pinball, slide out the playfield glass, and raise the playfield.
With the front door (coin door) open, move the lock down bar latch throughout and get rid of the lock down bar. Move out the playfield glass, and put in a safe location. Next, lift up the playfield by putting your hand where the ball drains, and lift the playfield up.
You should now have access to any nuts that may have been utilized. As soon as any nuts have actually been eliminated, change the playfield glass and lock down bar, and lock the front door.
Make sure to mark or remember which legs are for the front and back, as they will be adjusted differently to Get More Info suit.
Filling the Pinball.
You are now all set to carry your pinball device. Before you load it, make sure you remove the pinballs so they do not bounce around throughout transportation.
If you are moving the pinball using a van or SUV, it might be much easier to eliminate the legs just prior to loading the machine. Get a good friend to assist and have one of you supporting the pinball, while the other removes the front legs.
Make sure you strap the pinball in, as you do not desire it moving if you need to stop all of a sudden!
For Electro-Mechanical pinball machines, you need to get rid of the headbox rear gain access to panel to acquire access to the bolts and plugs inside. (Some newer Williams and Bally pinballs do not have a different amp panel, it is part of the back glass panel. And later on Sega and Stern pinballs use a fluorescent tube for the back glass lighting).
If you are moving the pinball using a van or SUV, it may be much easier to eliminate the legs just prior to loading the maker. Get a buddy to help and have one of you supporting the pinball, while the other gets rid of the front legs.